Armada Technologies Pro-48 Solenoid Activator / Basic Test Tool

The Pro48 Tech Tool Solenoid Activator Test Tool is The "Must Have" basic tester for irrigation professionals.

 Here is what the PRO48 Tech Test Tool does:

• It Chatters - YES.  PRO48 Chatters Solenoids!
• Activates and Holds Solenoids Open.
• Generates and Traces with a 1Khz Tracing Tone.
• Checks Clock 24v Power Output.
• Tests for Open or Shorted Wiring.

The Armada Technologies Rquipment PRO48 Tech Tool uses 2 - 9v Batteries (not included).

The Pro48 TechTool Solenoid and Clock Checker is a new low cost test set for irrigation contractors and maintenance personnel. The Pro48 performs a series of simple procedures to test, verify, and identify solenoid, wire, and clock problems. Solenoids can be checked using either activation or chatter modes. Lost or buried solenoids are quickly found as well by listening for the chatter. Wiring can be verified and tagged with the built in tone generator function. Clocks also are tested for proper 24v transmission with a simple LED power check.

Made from a grommited, thick walled plastic case, the highly visible yellow Pro48 TechTool Solenoid Activator is designed for rugged use in the field.

The Pro48 TechTool is a portable, battery operated irrigation system tester and solenoid activator. Its functions include:

• Testing voltage/current from the clock
• Activating solenoids
• Testing solenoids for continuity
• Chatter the solenoid –for location of valve Sending tone to identify wires

Chatter the solenoid valve NOTE: The GOOD LED must illuminate under the “Solenoid and Activate mode” before using the chatter mode.

1. To chatter the solenoid for the purpose of locating the valve from the clock, turn the clock off and switch the Pro48 to OFF mode.
2. TURN OFF WATER to irrigation system.
3. Disconnect both the station and common wire from the controller
4. Connect the Pro48 by attaching the red lead to the station wire and the black lead to the common.
5. Select side switch to CHATTER and top Switch to SOLENOID mode.
6. Proceed to the field and listen for the chattering sound at the solenoid valve.

Sending Tone

1. To identify a single wire from a bundle of similar wires, attach the red lead to the station wire and the black lead to earth ground.
2. Switch to SEND TONE mode.
3. Proceed to opposite end of wire and trace the tone with any Pro200 Series inductive amplifier. Reception of tone and the red LED will be strongest and brightest on the subject wire.

Pro48 TechTool Solenoid Activator / Test Tool - Specifications

Armada Technologies  - PRO48 Specifications

Pro48 Pro TechTool - Solenoid Activator - Maintenance / Cleaning

Pro48 - Battery Replacement:

1. Turn the unit off.
2. Disconnect the unit from the circuit.
3. Remove the battery cover.
4. Replace the batteries (observe polarity).
5. Replace the battery cover.

Pro48 - Cleaning

Periodically wipe with a damp cloth and mild detergent; do not use abrasives or solvents.

One-Year Limited Warranty

Pro-Tech Equipment warrants to the original purchaser of these goods for use that these products will be free from defects in workmanship and material for one year, excepting normal wear and abuse. For all test instrument repairs, you must first request a Return Authorization Number by contacting our Customer Service department at (480) 926-8324. This number must be clearly marked on the shipping label. Ship units Freight Prepaid to: Pro-Tech Equipment 39780 Rattle Snake Dr., Queen Creek, AZ 85242 Mark all packages: Attention: TEST INSTRUMENT REPAIR. For items not covered under warranty (such as dropped, abused, etc.) repair cost quote available upon request.

Note: Prior to returning any test instrument, please check to make sure batteries are fully charged.

Pro48 Activating the Solenoid at the Clock

Battery Test

1. Connect the leads together.
2. Switch to SOLENOID ACTIVATE mode.
3. If the batteries are good (at least 10.5 volts) the SHORT LED will turn on.

Irrigation Controller "Clock" Test

1. With the clock on and turned to the station under test, switch to OFF mode.
2. Connect the red lead to the station wire and the black lead to common.
3. If proper voltage/current is detected, the CLOCK 24V AC LED will turn on. Solenoid Activate & Test NOTE: The TechTool cannot activate solenoids that run on AC voltage only. (For example, capacitor coupled solenoids)

Activating solenoid at the clock

1. To activate solenoids from the clock, turn the clock off and switch the Pro48 to OFF mode.
2. Connect the Pro48 by attaching the red lead to the station wire and the black lead to the common.
3. Switch to SOLENOID mode and select side switch to ACTIVATE.
4. The solenoid under test should activate and the GOOD LED (see display on the front of the Pro48) should turn on. If the solenoid does not activate, one of the following conditions may exist:
   • Possible Short: SHORT LED is on (< 10 Ohm)
   • Possible Open: OPEN LED is on (> 200 Ohm)
5. The Pro48 must be switched to the OFF mode to reset the unit after the solenoid is activated. NOTE: If the GOOD LED does not illuminate, the solenoid should be tested at the valve.